sep.2000 m e q a n k n k n b g j c f r r g d h l tab#110 t=0.5 k p - dia. (4 typ.) c2e1 e1 c1 e2 c2 e2 c1 s - m6 thd. (3 typ) c2 e2 c2e1 e1 c1 e2 c1 dimensions inches millimeters a 4.33 110.0 b 3.661 0.01 93.0 0.25 c 3.15 80.0 d 2.441 0.01 62.0 0.25 e 1.18 max. 30.0 max. f 1.18 30.0 g 0.98 25.0 h 0.85 21.5 j 0.83 21.2 dimensions inches millimeters k 0.71 18.0 l 0.59 15.0 m 0.55 14.0 n 0.28 7.0 p 0.26 dia. dia. 6.5 q 0.33 8.5 r 0.24 6.0 s m6 metric m6 description: mitsubishi igbt modules are de- signed for use in switching appli- cations. each module consists of two igbts in a half-bridge configu- ration with each transistor having a reverse-connected super-fast re- covery free-wheel diode. all com- ponents and interconnects are iso- lated from the heat sinking base- plate, offering simplified system assembly and thermal manage- ment. features: u low drive power u low v ce(sat) u discrete super-fast recovery free-wheel diode u high frequency operation u isolated baseplate for easy heat sinking applications: u ac motor control u motion/servo control u ups u welding power supplies ordering information: example: select the complete part module number you desire from the table below -i.e. cm300dy- 24h is a 1200v (v ces ), 300 am- pere dual igbt module. type current rating v ces amperes volts (x 50) cm 300 24 mitsubishi igbt modules CM300DY-24H high power switching use insulated type outline drawing and circuit diagram
sep.2000 absolute maximum ratings, t j = 25 c unless otherwise specified symbol ratings units junction temperature t j C40 to 150 c storage temperature t stg C40 to 125 c collector-emitter voltage (g-e short) v ces 1200 volts gate-emitter voltage (c-e short) v ges 20 volts collector current (t c = 25 c) i c 300 amperes peak collector current i cm 600* amperes emitter current** (t c = 25 c) i e 300 amperes peak emitter current** i em 600* amperes maximum collector dissipation (t c = 25 c, t j 150 c) p c 2100 watts mounting torque, m6 main terminal C 1.96 ~ 2.94 n m mounting torque, m6 mounting C 1.96 ~ 2.94 n m weight C 500 grams isolation voltage (main terminal to baseplate, ac 1 min.) v iso 2500 vrms *pulse width and repetition rate should be such that the device junction temperature (t j ) does not exceed t j(max) rating. **represents characteristics of the anti-parallel, emitter-to-collector free-wheel diode (fwdi). static electrical characteristics, t j = 25 c unless otherwise specified characteristics symbol test conditions min. typ. max. units collector-cutoff current i ces v ce = v ces , v ge = 0v C C 1.0 ma gate leakage current i ges v ge = v ges , v ce = 0v C C 0.5 m a gate-emitter threshold voltage v ge(th) i c = 30ma, v ce = 10v 4.5 6.0 7.5 volts collector-emitter saturation voltage v ce(sat) i c = 300a, v ge = 15v C 2.5 3.4** volts i c = 300a, v ge = 15v, t j = 150 c C 2.25 C volts total gate charge q g v cc = 600v, i c = 300a, v ge = 15v C 1500 C nc emitter-collector voltage v ec i e = 300a, v ge = 0v C C 3.5 volts ** pulse width and repetition rate should be such that device junction temperature rise is negligible. dynamic electrical characteristics, t j = 25 c unless otherwise specified characteristics symbol test conditions min. typ. max. units input capacitance c ies C C 60 nf output capacitance c oes v ge = 0v, v ce = 10v C C 21 nf reverse transfer capacitance c res C C 12 nf resistive turn-on delay time t d(on) C C 250 ns load rise time t r v cc = 600v, i c = 300a, C C 500 ns switching turn-off delay time t d(off) v ge1 = v ge2 = 15v, r g = 1.0 w C C 350 ns times fall time t f C C 350 ns diode reverse recovery time t rr i e = 300a, di e /dt = C600a/ m s C C 250 ns diode reverse recovery charge q rr i e = 300a, di e /dt = C600a/ m s C 2.23 C m c thermal and mechanical characteristics, t j = 25 c unless otherwise specified characteristics symbol test conditions min. typ. max. units thermal resistance, junction to case r th(j-c) per igbt C C 0.06 c/w thermal resistance, junction to case r th(j-c) per fwdi C C 0.12 c/w contact thermal resistance r th(c-f) per module, thermal grease applied C C 0.035 c/w mitsubishi igbt modules CM300DY-24H high power switching use insulated type
sep.2000 mitsubishi igbt modules CM300DY-24H high power switching use insulated type collector-emitter voltage, v ce , (volts) collector current, i c , (amperes) output characteristics (typical) 0246810 360 120 0 v ge = 20v 15 12 11 8 7 t j = 25 o c 240 480 600 10 9 gate-emitter voltage, v ge , (volts) collector current, i c , (amperes) transfer characteristics (typical) 048121620 480 360 240 120 0 v ce = 10v t j = 25 c t j = 125 c 600 collector-current, i c , (amperes) collector-emitter saturation voltage, v ce(sat) , (volts) collector-emitter saturation voltage characteristics (typical) 5 0 120 240 360 480 4 3 2 1 0 600 v ge = 15v t j = 25 c t j = 125 c gate-emitter voltage, v ge , (volts) collector-emitter saturation voltage, v ce(sat) , (volts) collector-emitter saturation voltage characteristics (typical) 10 048121620 8 6 4 2 0 t j = 25 c i c = 120a i c = 600a i c = 300a emitter-collector voltage, v ec , (volts) free-wheel diode forward characteristics (typical) emitter current, i e , (amperes) collector-emitter voltage, v ce , (volts) capacitance, c ies , c oes , c res , (nf) capacitance vs. v ce (typical) 10 -1 10 0 10 2 10 2 10 1 10 0 10 -1 v ge = 0v 10 1 c ies c oes c res emitter current, i e , (amperes) reverse recovery time, t rr , (ns) reverse recovery characteristics (typical) 10 3 10 1 10 2 10 3 10 2 10 1 t rr i rr di/dt = -600a/ m sec t j = 25 c 10 2 10 1 10 0 reverse recovery current, i rr , (amperes) gate charge, q g , (nc) gate-emitter voltage, v ge , (volts) gate charge, v ge 20 0 600 1200 16 12 8 4 0 1800 2400 v cc = 600v v cc = 400v i c = 300a collector current, i c , (amperes) half-bridge switching characteristics (typical) 10 3 10 1 10 2 10 3 10 2 10 1 t d(off) t d(on) t r v cc = 600v v ge = 15v r g = 1 w t j = 125 c t f switching time, (ns) 10 1 10 3 7 5 3 2 1.0 1.5 2.0 10 2 7 5 3 2 2.5 3.0 3.5 t j = 25 c
sep.2000 mitsubishi igbt modules CM300DY-24H high power switching use insulated type normalized transient thermal impedance, z th(j-c) transient thermal impedance characteristics (igbt) 10 1 10 -5 10 -4 10 -3 10 0 10 -1 10 -2 10 -3 10 -3 10 -2 10 -1 10 0 10 1 single pulse t c = 25 c per unit base = r th(j-c) = 0.06 c/w z th = r th ?(normalized value) 10 -1 10 -2 10 -3 time, (s) time, (s) normalized transient thermal impedance, z th(j-c) transient thermal impedance characteristics (fwdi) 10 1 10 -5 10 -4 10 -3 10 0 10 -1 10 -2 10 -3 10 -3 10 -2 10 -1 10 0 10 1 single pulse t c = 25 c per unit base = r th(j-c) = 0.12 c/w z th = r th ?(normalized value) 10 -1 10 -2 10 -3
|
